Ausmini
It is currently Sat Jun 28, 2025 2:08 pm

Board index » Mini Chat » Mini & A/A+ Series Mods

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 1
  [ 9 posts ] 
  Print view Previous topic | Next topic 
Author Message
Flying Brick
PostPosted: Fri Jun 03, 2005 12:18 pm 
Offline
848cc
848cc

Joined: Mon Apr 11, 2005 1:18 pm
Posts: 226
Location: Canberra ACT
Im sure someone here has replaced a floorpan in a mini before, I am just wondering if you can get them for a mini with fluid suspension, they have the channel down the middle and an extra rib. I have bought one for my 850 and it fits(no channel in 850), all the ones i have seen on ebay and the one i bought dont have the channel. If you cant get one for the hydro setup, is it possible to put the other one in. The ribs dont line up.
I have 4 minis and 3 have the drivers floorpan cut out ready to replace.
Steve.
Top
 Profile  
 
rampage101
 Post subject:
PostPosted: Fri Jun 03, 2005 12:55 pm 
Offline
998cc
998cc
User avatar

Joined: Wed Mar 17, 2004 8:52 am
Posts: 734
Location: NSW Australia
Afaik you can't get them anymore in Aus. Please correct me if I'm wrong.
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Fri Jun 03, 2005 2:21 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39752
Location: near Baulkham Hills, NSW
All the ones I've seen here are UK made, with no pipe channels as they didn't have them over there.
Also, they are a bit thinner than ours- when I did Anton's 850 the original floor was 1.6mm, the UK front pans I bought were 1.0mm.
Yes the ribs don't line up properly, even on the 850 shell. :cry:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
MiniK
 Post subject:
PostPosted: Fri Jun 03, 2005 4:23 pm 
Offline
998cc
998cc
User avatar

Joined: Tue Mar 16, 2004 5:01 pm
Posts: 1090
Location: Penrith, NSW
Same problem here and its a pain in this ass :evil:

_________________
[Maverick] 1971 Mini K
Top
 Profile  
 
9YaTaH
PostPosted: Fri Jun 03, 2005 4:33 pm 
Offline
1360cc
1360cc
User avatar

Joined: Sun Apr 11, 2004 11:32 am
Posts: 12390
Location: Sthrn HiLoLands, NSW, Australia
Flying Brick wrote:
Im sure someone here has replaced a floorpan in a mini before, I am just wondering if you can get them for a mini with fluid suspension, they have the channel down the middle and an extra rib. I have bought one for my 850 and it fits(no channel in 850), all the ones i have seen on ebay and the one i bought dont have the channel. If you cant get one for the hydro setup, is it possible to put the other one in. The ribs dont line up.
I have 4 minis and 3 have the drivers floorpan cut out ready to replace.
Steve.


Steve...a car has just been cut up in Canberra for just that reason...looks like you need to find a donor shell (or three)... :idea:

_________________
"Show me the Mini!"
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Fri Jun 03, 2005 5:08 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39752
Location: near Baulkham Hills, NSW
You could replace all 4 pans, or get a whole floor? then clip the pipes and stuff on like early Mini Deluxe and Cooper S had. No channels in floor. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
justminis
 Post subject:
PostPosted: Fri Jun 03, 2005 8:38 pm 
Offline
998cc
998cc
User avatar

Joined: Fri Mar 26, 2004 8:44 pm
Posts: 1084
Location: Far North Queensland
I had to replace both front floors on my 70 K sprint mini, used the ready available floor pans and had my friendly sheetmetal guy bend up some channels that I then inserted in the appropriate place in the floor. A bit of work but it worked. Stiffened up the floor too.

_________________
Steve
Top
 Profile  
 
Flying Brick
 Post subject:
PostPosted: Mon Jun 06, 2005 8:30 am 
Offline
848cc
848cc

Joined: Mon Apr 11, 2005 1:18 pm
Posts: 226
Location: Canberra ACT
Thanks for all the replys and ideas, i havnt had the net for the weekend so i have only seen them now. I guess i will try and find a shell to cut up, or maybe i will put the replacement panel in and just have them going along touching the panel, they have the cover over them so they should be ok.
Thanks again.
Steve.
Top
 Profile  
 
rampage101
 Post subject:
PostPosted: Mon Jun 06, 2005 10:39 am 
Offline
998cc
998cc
User avatar

Joined: Wed Mar 17, 2004 8:52 am
Posts: 734
Location: NSW Australia
Well while were on the subject, does anywhere in Aus sell complete floor pans as opposed to 4x floor pan sections??
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 9 posts ] 

Board index » Mini Chat » Mini & A/A+ Series Mods

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 12 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.