Ausmini
It is currently Sun Jun 29, 2025 7:30 pm

Board index » Mini Chat » Mini & A/A+ Series Mods

All times are UTC + 10 hours




Post new topic Reply to topic  Page 1 of 1
  [ 13 posts ] 
  Print view Previous topic | Next topic 
Author Message
Lillee
PostPosted: Sat Jun 11, 2005 10:32 pm 
Offline
1360cc
1360cc
User avatar

Joined: Tue Jun 01, 2004 3:41 pm
Posts: 6858
Location: Special Tuning Sydney
I still can't get over my door prize at Graham Russel's today!!! :lol: OMG I was expecting the prize to be a keyring or something geeky like that but a fully ported head with unleaded valve seats :shock: Holy Fast Metal Batman!

Well then, what do I need to bolt this baby in? Here is my preliminary list:

Head Gasket (I'll get this from Greg M)
New Cam followers (Karcraft?)
New rocker cover gasket (already got)
Tappet cover gasket x2
1 RE13 cam 8)

Anything else? to take the cam out do I need to replace any gaskets down there?

I might go Dyno Lillee at Greg's before the head and cam (stocko 1098 with a dellorto and extractors), then after the head and cam to see what the difference is. Could be interesting... I think it will be close to Mini Mad's clubman at around 45bhp at the wheels... What do you reckon? does that mean Lillee is running a good 30 BHP now? (What a beast! :lol: )

_________________
Lillee - 1969 Morris Mini K
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sun Jun 12, 2005 7:53 am 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39752
Location: near Baulkham Hills, NSW
Get an `ACL' VRS gasket set off Greig, that has head gasket, manifold, rocker cover & the thermostat and heater ones too..

You will also need a timing cover gasket and seal.
:!: Fit your double row timing chain while you're in there...

Karcraft's cam followers are good (~$50/set)

I'll swap you my spare RE-13 (will get GR to freshen it up) for your stock S cam blank & $50. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
gafmo
 Post subject:
PostPosted: Sun Jun 12, 2005 9:13 am 
Offline
the King of Bling
User avatar

Joined: Thu Jun 03, 2004 11:11 pm
Posts: 19858
Location: Baulkham Hills
carton of Beer also :wink:

_________________
Stop Licking the Dog...I Don't Care Who Started It
Top
 Profile  
 
1310/71
 Post subject:
PostPosted: Sun Jun 12, 2005 9:20 am 
Offline
1275cc
1275cc

Joined: Mon Mar 22, 2004 7:41 pm
Posts: 4319
Location: Plumpton, NSW
drmini in aust wrote:
Get an `ACL' VRS gasket set off Greig, that has head gasket, manifold, rocker cover & the thermostat and heater ones too..

You will also need a timing cover gasket and seal.
:!: Fit your double row timing chain while you're in there...

Karcraft's cam followers are good (~$50/set)

I'll swap you my spare RE-13 (will get GR to freshen it up) for your stock S cam blank & $50. :wink:


Yeah, but to fit the double row timing chain, you need to countersink the backing plate and use the allen head screws. You won't be able to do that with it still on the engine will you?
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Sun Jun 12, 2005 11:25 am 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39752
Location: near Baulkham Hills, NSW
I have a GMC right angle drill... :P 8)
<edit> so does Chong... :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:


Last edited by drmini in aust on Mon Jun 13, 2005 12:39 pm, edited 1 time in total.

Top
 Profile  
 
Lillee
 Post subject:
PostPosted: Mon Jun 13, 2005 9:45 am 
Offline
1360cc
1360cc
User avatar

Joined: Tue Jun 01, 2004 3:41 pm
Posts: 6858
Location: Special Tuning Sydney
Sweet! I think my gearbox rebuild kit has a timing cover gasket... right?

So all I need is tappet cover gasket, the head gaskets from Greg and karcraft cam followers...

Sweeeeeet 8)

_________________
Lillee - 1969 Morris Mini K
Top
 Profile  
 
graham in aus
 Post subject:
PostPosted: Mon Jun 13, 2005 9:46 am 
Offline
1098cc
1098cc
User avatar

Joined: Thu Jul 15, 2004 9:53 pm
Posts: 1768
Location: Lake Macquarie NSW
Has head been skimmed? I thought 295 cc was large as stock due to cooper flat tops? won't it need a skim to suit the 1100? :roll:

_________________
Sir Alec! we are not worthy!
Top
 Profile  
 
Spaceboy
 Post subject:
PostPosted: Mon Jun 13, 2005 11:01 am 
Offline
1360cc
1360cc

Joined: Mon Nov 01, 2004 4:36 pm
Posts: 7673
you want low compression for boost anyhoo :twisted:
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Mon Jun 13, 2005 11:34 am 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39752
Location: near Baulkham Hills, NSW
graham in aus wrote:
Has head been skimmed? I thought 295 cc was large as stock due to cooper flat tops? won't it need a skim to suit the 1100? :roll:

It's had a skim, but we do need to cc it.. :wink:
Spaceboy, I don't think Chong is considering putting a hairdryer on this motor.. :lol:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
CRU17Y
PostPosted: Mon Jun 13, 2005 11:48 am 
Offline
848cc
848cc
User avatar

Joined: Mon Jul 05, 2004 9:02 pm
Posts: 442
Location: Castle Hill
68Delux wrote:
I still can't get over my door prize at Graham Russel's today!!! :lol: OMG I was expecting the prize to be a keyring or something geeky like that but a fully ported head with unleaded valve seats :shock: Holy Fast Metal Batman!


How did you score this??

_________________
Jet Red Mini K

Image
Top
 Profile  
 
drmini in aust
 Post subject:
PostPosted: Mon Jun 13, 2005 12:40 pm 
Offline
religious status
religious status
User avatar

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39752
Location: near Baulkham Hills, NSW
We gave a ticket to everyone that came...
Chongy got lucky!! :lol:
no 2nd prize......!

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:
Top
 Profile  
 
CRU17Y
 Post subject:
PostPosted: Mon Jun 13, 2005 2:42 pm 
Offline
848cc
848cc
User avatar

Joined: Mon Jul 05, 2004 9:02 pm
Posts: 442
Location: Castle Hill
Damn, he is one lucky guy

_________________
Jet Red Mini K

Image
Top
 Profile  
 
Lillee
 Post subject:
PostPosted: Mon Jun 13, 2005 8:01 pm 
Offline
1360cc
1360cc
User avatar

Joined: Tue Jun 01, 2004 3:41 pm
Posts: 6858
Location: Special Tuning Sydney
Graham, yeah it's already had a fair bit off the head... We'll have to either test it or ask Graham what CR it's running.

No no blower necessary :wink:

I am confident that Lillee is currently perfectly setup within 95% so it will be interesting what numbers she will get out of Greg's dyno at current setup. once the head is on we'll try it again for laughs :wink:

_________________
Lillee - 1969 Morris Mini K
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 13 posts ] 

Board index » Mini Chat » Mini & A/A+ Series Mods

All times are UTC + 10 hours


Who is online

Users browsing this forum: No registered users and 21 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  

© 2016 Ausmini. All garage work involves equal measures of enthusiasm, ingenuity and a fair degree of irresponsibility.