ausmini • View topic - What plugs for pulsar dizzy

Board index » Mini Chat » Mini & A/A+ Series Mods

All times are UTC + 10 hours

What plugs for pulsar dizzy

Moderators: winabbey, simon k, poeee, Mick

Page 1 of 1

[ 8 posts ]

Print view

Previous topic | Next topic

Author

Message

72clubman

Post subject: What plugs for pulsar dizzy

Posted: Mon Jun 06, 2005 2:15 pm

848cc

Joined: Tue Jul 06, 2004 9:08 pm
Posts: 211
Location: Melbourne

As the topic says what are the best sort of plugs and gaps to run when you have a pulsar dizzy installed, or should you use the ones reccomended for a nissan pulsar

_________________
77 Leyland Clubman
1293cc, LCB extractors, pulsar dizzy (recurved), cooper s disc brakes, 40DCOE Weber

Top

Damo

Post subject:

Posted: Mon Jun 06, 2005 2:24 pm

848cc

Joined: Thu Jul 01, 2004 12:20 am
Posts: 111
Location: Melbourne, Australia (car); Savannah (GA), USA (me)

Somewhere in the original thread it stated:

"Plugs: NGK BP6ES, Bosch W6DC are also good.
Plug gaps- .040" fires OK with the stock Nissan 1.5 ohm coil to 8000 rpm"

I just reset my current plugs to a 0.035" gap for the time being, with no problems. I will change to the NGK BP6ES with a 0.040" gap next service and give it a try.

Top

drmini in aust

Post subject:

Posted: Mon Jun 06, 2005 5:19 pm

religious status

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39752
Location: near Baulkham Hills, NSW

Plugs are always chosen based on the motor, NOT the dizzy..
Whatever plugs you have running now will still be fine. Open 'em up a bit as said. If you get any misfiring, close them back up a bit. .035"- .040" usually OK. :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:

Top

Besser

Post subject: gap setting

Posted: Tue Jun 07, 2005 7:38 pm

998cc

Joined: Mon Apr 05, 2004 11:23 am
Posts: 581
Location: Eastern Melbourne

Read an indepth article on plug gap and the outcome was 0.8mm.

Forced induction or NA hot or std all came back to best overall performance from 0.8mm.

I did find interesting the note regarding spark energy and duration. Seems that atomisation and turbulance was the gremlin for plug deterioration. hmm go figure

Top

72clubman

Post subject:

Posted: Wed Jun 08, 2005 10:12 am

848cc

Joined: Tue Jul 06, 2004 9:08 pm
Posts: 211
Location: Melbourne

What is a plug gap of 035"- .040" in mm

_________________
77 Leyland Clubman
1293cc, LCB extractors, pulsar dizzy (recurved), cooper s disc brakes, 40DCOE Weber

Top

rampage101

Post subject:

Posted: Wed Jun 08, 2005 12:08 pm

998cc

Joined: Wed Mar 17, 2004 8:52 am
Posts: 734
Location: NSW Australia

Nope, the " stands for imperial measurment of inches, also ' stands for feet.

Edit:

Ie. 0.040" is 0.040 inches.
Ie. 3' is 3 feet.

Top

Damo

Post subject:

Posted: Wed Jun 08, 2005 1:23 pm

848cc

Joined: Thu Jul 01, 2004 12:20 am
Posts: 111
Location: Melbourne, Australia (car); Savannah (GA), USA (me)

72clubman wrote:

What is a plug gap of 035"- .040" in mm

0.8mm (divide by 25.4 mm to the inch) = approx. 0.032"

Top

drmini in aust

Post subject:

Posted: Wed Jun 08, 2005 5:48 pm

religious status

Joined: Fri Mar 19, 2004 6:19 pm
Posts: 39752
Location: near Baulkham Hills, NSW

Damo wrote:

72clubman wrote:

What is a plug gap of 035"- .040" in mm

0.8mm (divide by 25.4 mm to the inch) = approx. 0.032"

Or remember that 1.0mm = .040" near enough- (actually 0.03937") :wink:

_________________
DrMini- 1970 wasaMatic 1360, Mk1S crank, 86.6HP (ATW) =~125 @ crank, 45 Dellorto (38 chokes), RE282 sprint cam, 1.5 rockers, 11.0:1 C/R. :mrgreen:

Top

Page 1 of 1

[ 8 posts ]

Board index » Mini Chat » Mini & A/A+ Series Mods

All times are UTC + 10 hours

Who is online

Users browsing this forum: No registered users and 11 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: