ausmini :: View topic - KazJim's New Blower - Fitted ! (finally)

ausmini https://ausmini.com/forums/

KazJim's New Blower - Fitted ! (finally) https://ausmini.com/forums/viewtopic.php?f=5&t=8032	Page 1 of 2

Author:	kazjim [ Mon Jun 13, 2005 3:09 pm ]
Post subject:	KazJim's New Blower - Fitted ! (finally)
So, After months of avoiding it, i find out that the new Turbo is VERY, VERY close to the old one in terms of bolt patterns and mount points ! A few tweaks and it went on without a hitch.... New turbo is an IHI RHF-5 - Ball Bearing unit..... Still plan to build a new exhaust manifold, but i just couldnt wait....... The Old is on the right.... In all its Glory... The Old Turbo Entry The New Awaiting A 12G1316 head to complete the setup.... then we find out..... (Doing a Kev special.....) Stay cool J

Author:	sg [ Mon Jun 13, 2005 3:13 pm ]
Post subject:
Stay cool???? Shouldn't that be stay SPOOL? Looking sweet Kazjim....... any ideas on power hike?

Author:	kazjim [ Mon Jun 13, 2005 3:21 pm ]
Post subject:
The goal is over 100 at the wheels at the next dyno day.... So I've got some toys up my sleeve yet.... DRMINI Special Tuning Head (1316) Pressure Mapped Water injection S13 Silvia Intercooler (but where to put it ?) and some other toys...... J

Author:	sg [ Mon Jun 13, 2005 3:24 pm ]
Post subject:

Author:	aussie [ Mon Jun 13, 2005 3:27 pm ]
Post subject:
Niiice Dude! im with sg------>

Author:	kazjim [ Mon Jun 13, 2005 3:30 pm ]
Post subject:
Gotta keep in mind guys, this is basically a "Street-rebuild" 998 .... nothing real scary about it other than the RE-13 Variant cam .... (Its GR secret grind - but similar to the RE-13) its currently running about 73@wheels - so another 20 isnt going to be too hard....... J

Author:	awdmoke [ Mon Jun 13, 2005 4:07 pm ]
Post subject:	Re: KazJim's New Blower - Fitted ! (finally)
kazjim wrote: The Old is on the right.... I could be mistaken, but isn't the one on the right just a little bit smaller? Still a streeter? More like a sleeper - that huffer should generate some boost once you get the revs up. Looks like fun Mike

Author:	CRU17Y [ Mon Jun 13, 2005 4:13 pm ]
Post subject:
sweet stuff, now you can setup for a twin turbo.

Author:	Konzo [ Mon Jun 13, 2005 4:29 pm ]
Post subject:
that new turbo is ****** HUGE!

Author:	kazjim [ Mon Jun 13, 2005 7:18 pm ]
Post subject:
The Donor was a GTX Famila ...... They made about 166BHP so its certainly good for about 130@wheels .... Now, to get the rest of the systems up to scratch and start making some serious Mumbo ! J

Author:	Boostedmini [ Mon Jun 13, 2005 7:41 pm ]
Post subject:
James looking sweet dude, is the exhaust side that much bigger too, thta will make a massive difference for sure, do you know the a/r size of just a exhaust size T2, T2.5 etc

Author:	supercharged 850 [ Tue Jun 14, 2005 1:41 am ]
Post subject:
You'll need to raise your suspension to fit the big bore exhaust Sorry to burst some people's bubble... but twin turbos on a 5 port head... technically cant happen. (even if you COULD fit it)

Author:	Mini Mad [ Tue Jun 14, 2005 1:51 am ]
Post subject:
james..very cool..

Author:	Lillee [ Tue Jun 14, 2005 9:02 am ]
Post subject:
Is it just me or is that thing like twice the size! Can't wait to see the yellow beast running with that James!

Author:	kazjim [ Tue Jun 14, 2005 9:23 am ]
Post subject:
Ive just been told that it may NOT be off a GTX.. but rather an Early WRX STI ! (in which case the A/r maybe right off . . . .) the exhaust housing is similar in size to my existing one, but the turbine is more "open" (hopefully the lighter ball bearing cartridge will offset the "looser" turbine wheel.....) Oh well, its all fun isnt it ? gotta give it a go ..... J

Page 1 of 2	All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/