all i can say is you can get to the speedo cable from underneath
| ausmini https://ausmini.com/forums/ |
|
| Quick question about speedos? https://ausmini.com/forums/viewtopic.php?f=5&t=29670 |
Page 1 of 1 |
| Author: | slo_firo [ Mon Mar 26, 2007 9:11 am ] |
| Post subject: | Quick question about speedos? |
i got a metro engine in my mini, now ive been driving it around with one of 92's supercharger kits on but my speedo doesnt work, Now im sure it was pushed into the gearbox properly but i can turn it at the speedo end so it obviously isnt connected right i dont want to have to pull everything out again to check cos i just got it running mint so.... i assumed the metro speedo drive was the same as a mini? am i right? any hints or tips on changing it without pulling everything apart again? cheers |
|
| Author: | Spaceboy [ Mon Mar 26, 2007 12:12 pm ] |
| Post subject: | |
all i can say is you can get to the speedo cable from underneath
|
|
| Author: | Mick [ Mon Mar 26, 2007 10:37 pm ] |
| Post subject: | |
ha ha yeah good fun. It helps if you have an extra wrist joint! |
|
| Author: | slo_firo [ Tue Mar 27, 2007 6:22 am ] |
| Post subject: | |
hahaha tried that already lol, pulled the borrom extra mount off ect... my hands are still too damn big, wish i was still 10, i had to do the same job on my dads mini and had the perfect hands to do so ive got the cable out of the sleeve when i push it back down and twist it i cant feel it even trying to line up in the slot.... which is why i was wondering if the metro is maby a bigger drive |
|
| Author: | slo_firo [ Thu Mar 29, 2007 6:52 am ] |
| Post subject: | |
ok had enough messing around!! bloody rads coming out tonight, my hands are sick of being crushed and cut up (can barly move one of my fingers from last nights effort) if i still cant get it im gng to mount a bike speedo on my rear hub and have a digital 1 lol |
|
| Author: | Spaceboy [ Thu Mar 29, 2007 8:57 am ] |
| Post subject: | |
use a long flathead screwdriver and a hammer, and tap the speedo cable "nut" loose be persistent, it may take awhile. i think getting the radiator in and out is more trouble than the speedo cable itself |
|
| Author: | slo_firo [ Thu Mar 29, 2007 10:57 am ] |
| Post subject: | |
yea theres just no way in hell i cn get my hands in there to do it, rads coming out tonight, b***h of a job but i kind of have to, give me a chance to check pully clearances ect... on the supercharger manifold anyway (put together in a hurry cos i wanted to drive it) |
|
| Author: | 9YaTaH [ Thu Mar 29, 2007 7:06 pm ] |
| Post subject: | cut metal... |
You can remove one of the slats in the inner guard to make it easier to get at... 
|
|
| Author: | cush [ Thu Mar 29, 2007 7:34 pm ] |
| Post subject: | |
slo_firo wrote: yea theres just no way in hell i cn get my hands in there to do it, rads coming out tonight, b***h of a job but i kind of have to, give me a chance to check pully clearances ect... on the supercharger manifold anyway (put together in a hurry cos i wanted to drive it)
i hope you read this first... http://www.ausmini.com/forums/viewtopic ... 370#165370 |
|
| Author: | slo_firo [ Fri Mar 30, 2007 6:19 am ] |
| Post subject: | |
havnt started it yet, read on turbo minis that metro drives are bigger than mini drives so my cable wont be any good anyway - can any one confirm? if this is the case to hell with it im getting a digi speedo to run off the hub, will look pretty damn flash lol |
|
| Author: | Spaceboy [ Fri Mar 30, 2007 3:55 pm ] |
| Post subject: | |
sigh, i've done this job more times than i'd have liked to, and i'm telling you thats how ya do it.. it does work. i think the bike speedo or whatever is dodgy. |
|
| Page 1 of 1 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|