ausmini
https://ausmini.com/forums/

written off mpi mini
https://ausmini.com/forums/viewtopic.php?f=2&t=400		 Page 1 of 1
Author:  ausminis4u [ Wed Apr 21, 2004 7:24 pm ]
Post subject:  written off mpi mini
where can i buy a writen off mpi mini from? i want a mpi clubman :) anyone got ideas, japans out tho , they dont auction writeoffs :( (as far as i have been told)
Author:  drmini in aust [ Wed Apr 21, 2004 7:28 pm ]
Post subject: 
One question- WTF would you want one? U can get more power with less hassle, with carbs, and hardly any bastard in Australia could tune an MPI Mini anyway...

my 2c- ah jest loves carbs! (preferably of Italian manufacture...) :twisted:
Author:  ausminis4u [ Wed Apr 21, 2004 7:31 pm ]
Post subject: 
drmini in aust wrote:
One question- WTF would you want one? U can get more power with less hassle, with carbs, and hardly any bastard in Australia could tune an MPI Mini anyway...

my 2c- ah jest loves carbs! (preferably of Italian manufacture...) :twisted:
yeh , well i was just thinking of another option i do have a dellorto :twisted: ready to put on , excepti need a new float chamber lid for it :(
Author:  min13k [ Wed Apr 21, 2004 7:42 pm ]
Post subject: 
you can buy a a+ motor from car craft
makka
Author:  ausminis4u [ Wed Apr 21, 2004 8:03 pm ]
Post subject: 
min13k wrote:
you can buy a a+ motor from car craft
makka
how much tho ? $800 plus i bet
Author:  min13k [ Wed Apr 21, 2004 8:41 pm ]
Post subject: 
bout that
makka
Author:  speedfreak [ Wed Apr 21, 2004 9:19 pm ]
Post subject: 
hey, you can prob get frount cuts from brickworkx in SA.

their isnt anywhere in aus that can tune efi/mpi etc mini. but they dont really need to be cos its all done by the computer. For example if you change a part it takes a short time for the computer to proform at its best.

Cheers Rob
Author:  -=MiniMafia=- [ Wed Apr 21, 2004 9:27 pm ]
Post subject: 
hey man u got that carb yet? :(
Author:  drmini in aust [ Wed Apr 21, 2004 9:42 pm ]
Post subject: 
Rob yeah I know they tune themselves, so does my EA Ford, haha- but what do you do when it f**ks up... I don't think anyone has the test gear over here, never mind the parts..! :wink:
Author:  supercharged 850 [ Thu Apr 22, 2004 12:53 am ]
Post subject: 
MPI???? ( does this mean multi point injection??? )

if the above is correct, brickworx here in adelaide has a few coming in soon... 80,000km 1.3i, air con, 8.4 disc brakes, in a front half cut, with the bonnet, gaurds, subframe, dash, steering column, wiring etc...... $4 large (thats 4 thousand dollars in old peoples language)

not too bad really....

or for $9 large ( thats 9 thousand.... ) you could get a complete '94 model Jap Spec mini - 1000cc, air con, auto, approved for compliance and registration in SA..... friend of mine just ordered one.....
Author:  dr trim [ Thu Apr 22, 2004 3:11 am ]
Post subject: 
/me shuts mouth before i say anything about brickworx :roll:
Author:  marconi [ Thu Apr 22, 2004 6:29 pm ]
Post subject: 
Sounds Like an exellent thing to weld staight on the fron of a clubie!

BTY who's going to wakefield on Sat
Author:  ausminis4u [ Thu Apr 22, 2004 7:16 pm ]
Post subject: 
marconi wrote:
Sounds Like an exellent thing to weld staight on the fron of a clubie!

BTY who's going to wakefield on Sat
i would luv to but cant get there :(
Author:  supercharged 850 [ Fri Apr 23, 2004 1:02 am ]
Post subject: 
brickworx is fine AS LONG as you do the following.....

1. know your prices.
2. walk in with cash, walk out with your item.
3. or pay only when you receive the item.

if you're stupid with your money, you WILL get bitten. these are general rules for ALL shops, not just brickworx.....

(some of us are lucky enough to get credit at certain shops :wink: )
Author:  mutant mini [ Wed Apr 28, 2004 2:17 pm ]
Post subject: 
Anyone know who is doing the compliance in S.A.?
Page 1 of 1 All times are UTC + 10 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/