| ausmini https://ausmini.com/forums/ |
|
| Hydrolastic Pump parts https://ausmini.com/forums/viewtopic.php?f=2&t=84853 |
Page 1 of 1 |
| Author: | mitchell evans [ Sun Mar 09, 2014 1:22 pm ] |
| Post subject: | Hydrolastic Pump parts |
Hi don't know if this is the right section for this I recently purchased a hydrolastic pump it works but leaks a bit from the pump seals and the vacuum side is missing the fitting off the end and gauge isn't working can parts be sourced for these? as I'd like to restore it/tidy it up any help would be great even what colour it should be thanks   
|
|
| Author: | boomini [ Sun Mar 09, 2014 5:20 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
Where do you find this stuff mitch? |
|
| Author: | Babes [ Sun Mar 09, 2014 5:57 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
Bought that from a guy off gumtree recently im guessing, I rang him he told me people were calling from all over the country offering more than what he was asking |
|
| Author: | peterb [ Sun Mar 09, 2014 6:53 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
the guage can be repaired usually, the 'end' you refer to I asume is the hose end?, just an old tyre valve chuck. Our 'original' one was sort of light green hammer tone. |
|
| Author: | mitchell evans [ Sun Mar 09, 2014 7:20 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
Yes it's the one that was on Gumtree Thanks Peter what about the seals in the actual pump(like the ram) can you get them? |
|
| Author: | peterb [ Sun Mar 09, 2014 7:25 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
I've never actually had one apart but if BMC is associated with it, it won't be too tricky, more than likely rusty in bore/ram. Rip it apart and have a look, probably o rings or similar. |
|
| Author: | drmini in aust [ Sun Mar 09, 2014 7:51 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
morris 1100 is the expert on these pumps... 
|
|
| Author: | michaelb [ Sun Mar 09, 2014 8:18 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
Mine is black |
|
| Author: | winabbey [ Mon Mar 10, 2014 10:46 am ] |
| Post subject: | Re: Hydrolastic Pump parts |
First, the good news.  Below is a BMC Technical Bulletin that might help you understand how the pump works.Now, the bad news.  The repair kits are no longer available.But some more good news. As stated, Morris 1100 on here has refurbished these so could help you locate the component parts. Also, I can give you the name of someone else who has overhauled several so may also be of help. Just PM me.    
|
|
| Author: | mitchell evans [ Wed Oct 29, 2014 5:09 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
Getting to the finishing stages of the rebuild of this pump. I got some seals made up for the pressure side(the left side)they couldn't make them to the original ones, they used poly bush however it still leaks a bit So my question is has anyone got some make up that work? If so where from any help would be great Thanks Mitch  
|
|
| Author: | winabbey [ Wed Oct 29, 2014 7:05 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
PM 850man and Morris 1100 on here as they have both refurbished these pumps. 850man also sells repro instruction plates that screw to the top. |
|
| Author: | Babes [ Wed Oct 29, 2014 7:18 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
Mitch its no good mate, has a fly on it so must be buggered. As im such a nice bloke I'll take it off your hands and save you the hassles. Im good like that. |
|
| Author: | mitchell evans [ Wed Oct 29, 2014 9:29 pm ] |
| Post subject: | Re: Hydrolastic Pump parts |
I have a new plate to go on the top pretty sure I got it from him Jason it has been a lot messing around for this thing trying to get lines and fittings I'll be happy once its done! |
|
| Page 1 of 1 | All times are UTC + 10 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|